Call Us Today!

Call Us Today!

Call Us Today!

Our Blogs

How Do I Reset My Furnace?

Quick Answer: Most furnaces, gas or electric, don’t have a furnace reset button. You reset one by turning the thermostat off, switching off power at the furnace switch or breaker, waiting, then restoring it, following your owner’s manual. Reset once. If it shuts down again, a safety switch is stopping it, and it’s time to schedule a furnace repair.

Key Takeaways

  • Furnaces have built-in safety switches that shut them off when something is wrong. A reset lets the furnace try again, but it doesn’t fix what tripped the switch.
  • Check the thermostat, the power switch, and the filter before resetting anything.
  • Reset once. A furnace that keeps shutting down needs a diagnosis, not more resets.
  • Never bypass a safety switch, and never reset a furnace when you smell gas or a carbon monoxide alarm is sounding.

You reset most furnaces by turning off their power at the furnace switch or breaker, waiting as long as your owner’s manual specifies, and turning the power back on. There’s usually no furnace reset button to press. On a gas furnace, cutting the power clears a lockout, the waiting period a furnace enters after it fails to light or senses something unsafe, so it can try to start again. A reset only helps when the shutdown was a one-time event; if it keeps happening, the next step is a furnace repair visit, not more resets.

Whether that second attempt works tells you a lot. Clarke & Rush handles furnace repair across the Sacramento region, including furnaces that won’t stay running after a reset. Reset controls vary by manufacturer and model, so the instructions on your furnace door or in your owner’s manual come first.

When not to reset your furnace

Don’t reset a furnace, or touch it at all, if you smell gas or a carbon monoxide alarm is going off. Both call for leaving the house and getting emergency help.

Natural gas has a sulfur or rotten-egg odor added so leaks can be noticed. PG&E’s guidance if you smell gas is to leave the area immediately, avoid using light switches, phones, or anything that could create a spark on the way out, and call 911 once you’re at a safe distance. You can also report the leak to PG&E at 1-800-743-5000.

A carbon monoxide alarm is just as urgent. The U.S. Consumer Product Safety Commission’s guidance is to never ignore a CO alarm, get outside immediately, and call 911 from a fresh-air location. Emergency responders will tell you when it’s safe to go back in. Carbon monoxide has no smell, so the alarm may be your only warning. More warning signs are covered in when you should turn off your furnace.

Also skip the reset if you see scorch marks, soot around the furnace, or a flame outside the burner area, or if you smell something burning beyond the light dust odor of the first heating cycle of the season. Turn the furnace off and call for service.

What resetting a furnace actually does

Resetting a furnace clears its control board after a safety shutdown so it can try to start again. It doesn’t fix anything mechanical.

The steps below focus on gas furnaces, the most common type in the Sacramento area, because ignition lockouts are a gas furnace feature. Electric furnaces are covered in their own section further down.

Every gas furnace follows a startup sequence. The thermostat calls for heat, the draft inducer fan starts, a pressure switch confirms the venting is clear, the hot surface ignitor glows (or a spark igniter clicks), the gas valve opens, and a flame sensor confirms the burners actually lit. If any step fails, the control board shuts off the gas and tries again.

After several failed tries, the board stops and enters a furnace lockout. The details vary by control. One widely used White-Rodgers ignition control, for example, makes four ignition attempts before locking out and then resets itself automatically after one hour. Other controls use different timing, which is why your owner’s manual matters.

A lockout is a safety feature. It keeps the furnace from repeatedly sending gas to burners that won’t light properly. Resetting the power skips the waiting period, but whatever caused the failed starts is still there.

Check the thermostat first

Many furnaces that seem to need a reset are fine, and the problem is the thermostat not calling for heat.

Check these before you touch the furnace:

  • The thermostat is set to HEAT, not COOL or OFF.
  • The setpoint is a few degrees above the current room temperature.
  • The screen is on. A blank or dim display usually means dead batteries or lost power.
  • The fan is set to AUTO. On ON, the blower runs constantly and can blow room-temperature air between heating cycles, which feels like a furnace that isn’t working.

The furnace’s own behavior helps separate a thermostat fault from a furnace fault. If you raise the setpoint and nothing happens at the furnace at all (no inducer fan, no click, no status light change), the thermostat or its wiring may not be sending the call for heat. If the furnace starts its sequence and then quits, the thermostat did its job, and the problem is in the furnace. A blank screen, a reading that doesn’t match the room, or a system that ignores the thermostat entirely points toward HVAC thermostat repair, not a furnace reset.

How to reset a gas furnace safely

To reset a gas furnace, cut its power for a short time and restore it, one time, after checking the basics. Follow your manufacturer’s instructions wherever they differ from these general steps.

  1. Turn the thermostat to OFF.
  2. Look through the small window on the furnace door for a status light. If it’s blinking a pattern, write it down. Most furnaces print a code chart on the inside of the door, and the code tells a technician where to start.
  3. Check the furnace filter. A clogged filter can overheat the furnace and trigger a safety shutdown. Replace it if it’s gray or packed with dust.
  4. Make sure the blower compartment door is fully seated. Most furnaces have a door safety switch that cuts power when the panel is loose.
  5. Find the furnace power switch, which often looks like a light switch on or near the furnace, or the furnace’s breaker in your electrical panel. Turn it off.
  6. Wait. The White-Rodgers control mentioned above needs power interrupted for at least ten seconds; check your manual for your model’s requirement.
  7. Turn the power back on, set the thermostat to HEAT, and raise the setpoint.
  8. Watch and listen. You should hear the inducer fan, then see the ignitor glow or hear it click, then the burners light, followed by the main blower.

If the furnace lights and keeps running, the shutdown may have been a one-time event. If it locks out again, stop. Don’t keep cycling the power.

How to reset an electric furnace

To reset an electric furnace, turn the thermostat off, switch off the furnace’s breaker or breakers, wait as your owner’s manual directs, and turn the power back on, one time.

An electric furnace has no burners, gas valve, or ignition sequence, so it doesn’t go into an ignition lockout. It heats with electric resistance elements, and each element is protected by limit switches that open when the element gets too hot. Many electric furnaces draw enough power to use more than one breaker, so check the panel for every breaker labeled for the furnace or air handler.

If a breaker has tripped, reset it once. A breaker that trips again, or a furnace that runs the blower but never delivers warm air, points to a failed element, a limit switch, or a wiring problem. Those involve high-voltage components, so call for service rather than resetting again or opening the cabinet.

Reset buttons you might find, and which to leave alone

Some furnaces and related equipment do have physical reset buttons, and most of them belong to safety switches that should be reset only after someone finds out why they tripped.

This table lists the reset controls you’re most likely to see and what each one means.

Control Where you’ll see it What it means What to do
Control board lockout Blinking status light on a gas furnace Repeated failed ignition or a safety trip Reset power once; call if it repeats
Flame rollout switch Small manual-reset button near the burners Flames left the combustion area Don’t reset; call for service
Blower motor thermal reset Button on some blower motors The motor overheated Call for service; the cause needs diagnosis
Oil burner reset Red button on the burner of an oil furnace The burner failed to light Press once only; call if it trips again
Electric heat limit Inside an electric furnace or air handler Heating elements overheated Call for service

The flame rollout switch deserves special mention. It detects flames escaping the combustion zone, which can happen with dirty burners, a blocked vent, or a cracked or blocked heat exchanger, and incomplete combustion in that situation can produce carbon monoxide. Manufacturer guidance is direct: multiple trips mean you need a technician, not a reset button.

Oil furnaces are uncommon in the Sacramento area, where gas furnaces are the most common type, but an oil burner’s red furnace reset button works differently from a gas furnace’s controls. Pressing it repeatedly can let unburned oil collect in the combustion chamber, so press it once at most.

Never bypass a safety switch or keep resetting a lockout

Bypassing a safety switch or resetting a lockout over and over removes the protections that keep a furnace from overheating, leaking gas, or venting carbon monoxide into the house.

Each safety switch watches for one specific danger. The high-limit switch shuts off the burners when the furnace overheats. The pressure switch keeps the burners off if exhaust isn’t venting properly. The flame sensor shuts off gas when it can’t confirm a flame. The rollout switch catches flames where they don’t belong. When one of them trips, it’s doing its job.

Removing or bypassing the rollout switch eliminates the only active protection against uncontrolled flame escape, and the same logic applies to every safety switch. Jumping a switch with a wire, taping a door switch closed, or resetting a lockout every hour to keep heat coming can turn a repairable problem into a fire or carbon monoxide hazard. When a furnace locks out more than once, the useful information is the reason, and a technician can read the status code and test each control to find it.

 

Why the first cold morning can bring a lockout in Sacramento

The first cold morning of the season can trigger a furnace lockout because parts that wore out or fouled while the furnace sat idle all summer are suddenly asked to work.

California homes rarely have basements, so many furnaces around Sacramento, Roseville, Elk Grove, and Folsom sit in an attic, a closet, or a garage. An attic furnace spends the summer in extreme heat even when it isn’t running, which is hard on wiring, seals, and electronic components. Winter tule fog adds sustained humidity that can corrode electrical connections and venting. Then the furnace goes from idle to working on a cold morning, and a weak ignitor, a fouled flame sensor, or a filter that’s been loading up since spring shows up as a lockout.

A fall furnace filter check and a test run on a mild afternoon, before you actually need heat, catch many of these problems while there’s time to schedule a repair.

When it’s time to call for furnace repair

It’s time to call for furnace repair if the furnace locks out again after one reset, if the status light shows a fault code, if a reset button on a safety switch has tripped, or if you see water, soot, or scorch marks around the furnace.

When you call, have the status light code, the furnace brand and model from the label on the door, and a description of what happens when the furnace tries to start. A gas furnace that never tries points to power, the thermostat, or a door switch. One that lights and then shuts off within seconds points toward the flame sensor. One that runs for a few minutes and then shuts off points toward overheating and airflow. That detail helps a technician arrive with the right parts.

Reset once, then find out why it stopped

A furnace reset is a one-time test, not a fix. Check the thermostat, the power switch, the filter, and the panel door first, reset once by following your manufacturer’s steps, and stop if the furnace locks out again. When a safety switch keeps shutting the furnace down, it’s protecting your home, and the reason it keeps tripping is what needs fixing. Clarke & Rush handles furnace repair throughout the Sacramento region when a reset doesn’t hold.

Frequently asked questions

Most modern gas and electric furnaces don’t have one. They reset by cycling power at the furnace switch or breaker. Some furnaces have a manual-reset flame rollout switch near the burners, and some blower motors have a thermal reset button, but those belong to safety switches and shouldn’t be pressed without knowing why they tripped. Oil furnaces typically have a red furnace reset button on the burner.

It depends on the control. One widely used White-Rodgers ignition control resets itself automatically after one hour of lockout, and others use different timing. Your owner’s manual lists the timing for your model. Waiting out a furnace lockout, or resetting it by cycling power, only gives the furnace another try. If it locks out again, the cause is still there.

Repeated lockouts usually trace to a failed ignition or a safety trip. Common causes include a dirty flame sensor, a worn ignitor, a blocked vent or condensate drain on a high-efficiency furnace, restricted airflow from a clogged filter, and low gas pressure. The status light code narrows the list. A technician can test each part of the startup sequence to find which one is failing.

Yes, once, if there’s no gas odor, no carbon monoxide alarm, and no sign of soot, scorching, or burning. Cycling the power at the furnace switch or breaker is a normal homeowner step. Bypassing switches, pressing a rollout switch reset, opening the burner compartment, or resetting a lockout repeatedly are not. If the furnace shuts down again, call for service.

Yes. A clogged filter cuts airflow across the heat exchanger, the furnace overheats, and the high-limit switch shuts off the burners. On many furnaces, repeated limit trips lead to a lockout. Replacing a dirty filter is one of the safest and cheapest things to try before a reset, and checking it monthly during heating season helps prevent the problem.

Start with the thermostat. Check that it’s set to HEAT with the setpoint above room temperature, that the screen is lit, and that the batteries are fresh. If the furnace shows no sign of starting when you raise the setpoint, the thermostat or its wiring may be the issue. If the furnace starts and then quits, the thermostat is working, and the furnace needs attention.

CONTACT US

We value your privacy and protect your information. Your details will only be used to assist with plumbing, heating, cooling and any other services you may need, and won’t be shared outside of necessary personnel.

Recent Posts