Quick Answer: A new furnace installation starts with an estimate visit to size the new furnace and check your ductwork, followed by a permit. Most installs take one day. The crew connects gas, venting, and wiring, then tests gas pressure, airflow, temperature rise, and venting before the inspection and a walkthrough of your new system.
Key Takeaways
- The new furnace should be sized to your home, not just matched to the size of the old one.
- Your ductwork gets evaluated before it’s reused, because a new furnace can only perform as well as the ducts it’s connected to.
- A mechanical permit and inspection are generally required, and California’s energy code may also call for a duct leakage test.
- Most residential installs are finished in one day. Duct changes can add time.
A new furnace installation usually follows a predictable path: an evaluation and sizing visit, a permit, one day of installation, a round of testing, and a final inspection and walkthrough. Knowing what happens at each stage helps you prepare your home, ask the right questions, and recognize a thorough job when you see one.
Clarke & Rush installs gas furnaces and packaged systems for homes across the Sacramento region, and this article follows the process its installation page lays out. Some details vary by home and jurisdiction, but the stages are the same for most residential installs.
Before installation day: evaluation and sizing
Before installation day, a technician visits your home, looks at your current system, and recommends a furnace in the right size and type.
The visit covers the things that affect sizing and comfort, such as square footage, insulation, existing ductwork, airflow, and any comfort problems you’ve noticed. The right size depends on the home, not on the size of the old unit, which may have been wrong from the start.
Sizing matters in both directions. An oversized furnace heats the house in short bursts and shuts off, known as short cycling, which wears parts faster and leaves rooms uneven. An undersized furnace runs constantly and struggles to keep up on cold mornings. The U.S. Department of Energy notes that a properly sized furnace operates most efficiently.
This is also when you’ll choose a model. Furnace efficiency is rated by AFUE, or annual fuel utilization efficiency, which the Department of Energy defines as how efficiently a furnace converts the energy in its fuel to heat. A 90% AFUE furnace turns 90% of the fuel’s energy into heat for the home. Clarke & Rush offers standard furnaces around 80% AFUE, high-efficiency models at 90% to 95%, and premium models at 96% or higher. You’ll also choose between single-stage, two-stage, and modulating heat, and whether you want a variable-speed blower.
Checking the ductwork before the new furnace goes in
The ductwork is evaluated before the new furnace is connected, because existing ducts are reused only if they’re sized for the new unit’s airflow and meet applicable leakage requirements, with sealing or modifications completed where needed.
Air duct problems can undo much of what a new furnace offers. The Department of Energy points out that AFUE doesn’t include heat lost through the duct system, which can be as much as 35% of the furnace’s output when ducts run through unconditioned spaces like an attic. Clarke & Rush checks connections and joints for leakage, a common reason some rooms run too warm or too cold, and confirms that the ducts can carry the airflow the new furnace needs.
If the ducts pass, they’re reconnected to the new furnace with new transitions where the old and new equipment don’t line up. If they don’t, expect a recommendation to seal, modify, or replace sections, and expect that work to add time to the project. If you’ve noticed warning signs before the install, such as rooms that never warm up, those are covered in signs your ductwork needs repair, and they’re worth mentioning during the evaluation.
Permits and California’s energy code
A new furnace generally requires a mechanical permit from your local building department, an inspection after installation, and compliance with California’s Title 24 energy code.
Clarke & Rush pulls the permit before work begins and coordinates the inspection. Requirements vary between jurisdictions across Sacramento, Placer, and Yolo counties, so the details depend on where you live. Under California’s energy code, installing new heating equipment in a ducted system can also trigger a duct leakage test, verified by an independent rater in the state’s Energy Code Compliance program, depending on the project and any exceptions that apply.
The permit process includes a required inspection, which may be virtual or in person depending on the jurisdiction and permit type. Ask who will coordinate it, whether you need to participate, and whether separate energy-code verification is required.
What happens on installation day
On installation day, the crew removes the old furnace, sets the new one, connects the gas, venting, electrical, and ductwork, and installs or connects the thermostat, and most residential jobs are finished the same day.
This table walks through the typical sequence and what you’ll notice at each step.
| Stage | What the crew does | What you’ll notice |
| Shutdown | Turns off gas and power to the furnace | No heat until the new system is running |
| Removal | Disconnects and removes the old furnace | Crew traffic to the attic, garage, or closet |
| Setting the unit | Places the new furnace and connects it to the ducts | Sheet metal work and some noise |
| Connections | Connects gas, venting, electrical, and the condensate drain on high-efficiency models | New vent pipes, sometimes in a new location |
| Thermostat | Installs or connects the thermostat | A new thermostat or updated settings |
| Testing | Verifies gas pressure, airflow, temperature rise, and venting | The furnace runs through several heating cycles |
Venting often changes the most. High-efficiency condensing furnaces, the 90% AFUE and higher models, typically vent through plastic pipe because their exhaust is cooler and acidic, and the Department of Energy notes that this exhaust isn’t suitable for old, unlined chimneys. Clarke & Rush sizes and routes venting by furnace category, since improper venting is a carbon monoxide risk. If you’re moving from an 80% furnace to a condensing model, ask where the new vent and condensate drain will run.
To prepare, clear a path to the furnace and the attic access, move cars if the furnace is in the garage, and plan for pets to be kept away from open doors and work areas.
Testing airflow, gas pressure, and venting
Before the job is done, the new furnace should be tested against the manufacturer’s specifications, including airflow testing, gas pressure, temperature rise, and venting.
Each check confirms something different. Gas pressure confirms the burners are getting the fuel they’re designed for. Airflow testing confirms the blower is moving enough air through the ducts. Temperature rise, the difference between the temperature of the air entering the furnace and the air leaving it, shows whether airflow and burner output are balanced; the acceptable range is printed on the furnace’s rating plate. Venting and combustion-safety checks confirm exhaust is leaving the house the way it should.
Clarke & Rush verifies gas pressure, venting, and combustion-safety requirements before a gas furnace is put into service, and checks airflow and temperature rise against the manufacturer’s specifications. Testing is where an installation proves it was done right, so it’s fair to ask what was measured and whether the readings fell within range.
Choosing and setting up the thermostat
A new furnace is a good time to upgrade the thermostat, but the thermostat has to match the furnace’s features and wiring.
A smart thermostat can offer remote control, automatic scheduling, and energy-use reports, depending on the model. Clarke & Rush works with major brands such as Nest, Ecobee, and Honeywell. Many smart thermostats need a C-wire, a dedicated wire that provides continuous power, and some homes need added wiring or an adapter. Confirm that the thermostat and furnace controls support the intended operation. Some two-stage furnaces manage staging internally, while other systems need a compatible multistage or communicating thermostat to provide their full functionality.
The final inspection and walkthrough
The project ends with the permit inspection and a walkthrough, where you learn how to operate the new system and what it needs from you.
The walkthrough covers how the system operates, how and when to replace the filter, maintenance intervals, and warranty coverage. Every Clarke & Rush installation is backed by the manufacturer’s equipment warranty and Clarke & Rush’s workmanship coverage, and the terms are reviewed during the walkthrough. Keep the paperwork and the permit record together. Regular maintenance, such as through the Energy Saving Plan, helps preserve performance and identify developing problems. Follow the manufacturer’s maintenance requirements and keep service records.
Furnace installation in a Sacramento-area home
In the Sacramento area, where the furnace sits and which jurisdiction issues the permit can shape the project as much as the furnace you choose.
California homes rarely have basements, so many furnaces in Sacramento, Roseville, Elk Grove, and Folsom are installed in attics, garages, or hall closets. Attic installs mean more work getting equipment in and out, and attic ducts are exposed to summer heat and winter cold, which makes the duct evaluation especially useful. Homes with no indoor space for a furnace can use a packaged unit, which Clarke & Rush installs as gas/electric systems that sit outside. And because permit rules vary across Sacramento, Placer, and Yolo counties, the contractor’s familiarity with your local building department matters.
A good installation starts before the old furnace comes out
The quality of a furnace installation is mostly decided before installation day, in the sizing, the duct evaluation, and the permit. When you compare estimates, ask how the furnace was sized, what the duct evaluation found, and what will be tested before the job is signed off. Clarke & Rush can walk you through each of those steps for your home.
Frequently asked questions
Most residential furnace installations are completed in one day, according to Clarke & Rush. Projects that involve new or modified ductwork, a change in furnace location, or new venting take longer. The permit inspection, virtual or in person depending on your jurisdiction, usually happens after installation. Ask for a schedule that covers the install, any duct work, and the inspection so you know how long you’ll be without heat.
Sometimes. Existing ducts can be reused if they’re sized for the new furnace’s airflow and meet applicable leakage requirements. That’s decided during the evaluation. If the ducts are undersized or leaky, you may need sealing, modifications, or replacement sections before or during the install, and California’s energy code may require a duct leakage test.
Not while the old furnace is out and the new one is being connected. Gas and power to the furnace are shut off at the start, and heat returns once the new system is connected and tested, usually the same day. On a cold day, plan for a few hours without heat, and ask the installer about timing if anyone in the home needs to stay warm.
Most homeowners choose a furnace between 90% and 96% AFUE, according to Clarke & Rush, though standard 80% models are also available. A higher rating converts more fuel to heat, but the right choice depends on your budget, how long you plan to stay in the home, and whether condensing-furnace venting fits your home’s layout.
Not always, but it’s often worth it. Your existing thermostat may work if it’s compatible with the new furnace. Some two-stage furnaces manage staging internally with a compatible single-stage thermostat, while other systems need a multistage or communicating thermostat for full functionality. Many smart thermostats also need a C-wire for continuous power, so check compatibility before buying one.
It can, but it isn’t guaranteed. A properly sized, higher-efficiency furnace often reduces heating costs, especially when it replaces an older, less efficient unit. Leaky ducts, thin insulation, and thermostat settings still affect what you pay, because AFUE measures the furnace alone, not the heat lost in the ducts or through the house.